Vivo Y Test Point Edl Point And Isp Pinout Xdarom Co Check “direct emmc (isp)”. then click on “ identify emmc. connect your vivo y12 to the pc via a usb cable. head over to the pc and open device manager. if your device is located there, run the ufi box. go to userareapart. now click on special task [vivo] masterclear wipe data only. Install “vivo y12 and y15 mtk usb drivers” on a windows pc. remove back panel of the device carefully. make sure you are not going to damage any hardware component. now check the below screenshot and find the vivo y12 test points. remove the battery and short bot points using any copper wire and attach a usb cable at the same time.
Isp Pinout Vivo Y12 Pd1901bf In this guide, we will show you the real image of the isp pinout and test point for the vivo y12s (pd2060f). by using the isp pinout, you can easily restore the stock rom, bypass frp lock, or reset user data on your device via ufi box. in this guide, we will also guide you on how to reboot into 9008 edl mode. The vivo y12 is a budget smartphone released in 2019, powered by a mediatek helio p35 mt6762 processor with either 3gb or 4gb of ram and 32gb or 64gb of internal storage, expandable up to 256gb via microsd card. it features a 6.35 inch ips lcd display with 720 x 1544 pixels resolution, a triple camera setup on the rear consisting of a 13mp. Method 3: hardware test points and device restoration. download the qdloader driver. on your device, locate the edl pinout test point (refer to the image above to find the test point) you must short the points using a metal tweezer or conductive metal wire to activate edl mode. when you’re finished, use a usb cord to connect your device to. How to connect vivo y12s (v2026) to edl mode. open the back cover first. vivo 2015 y1s ( be cautious when removing the cover on the back from the handset ) remove battery cable ( battery is not needed in edl mode ) you can now use tweezers to cut 2 dot point. dot point, as shown in the above image. connect the usb cable to your device.
Vivo Y12 Emmc Isp Pinout Test Point Edl Mode 9008 Images I Method 3: hardware test points and device restoration. download the qdloader driver. on your device, locate the edl pinout test point (refer to the image above to find the test point) you must short the points using a metal tweezer or conductive metal wire to activate edl mode. when you’re finished, use a usb cord to connect your device to. How to connect vivo y12s (v2026) to edl mode. open the back cover first. vivo 2015 y1s ( be cautious when removing the cover on the back from the handset ) remove battery cable ( battery is not needed in edl mode ) you can now use tweezers to cut 2 dot point. dot point, as shown in the above image. connect the usb cable to your device. How to reboot vivo y12s to 9008 edl mod: method 1: enable usb debugging. connect phone to pc. send the command via adb. adb reboot edl. method 2 (test point): install qd loader driver on computer. remove back cover of phone & find out the pinout as show in below image. How to reboot vivo y12a to edl mod: install qcom driver on your computer. remove back cover of phone & find out the pinout as show in below image. connect phone to computer by using usb cable. take a coper wire and short that pinout or you can do using tweezer. test point for vivo y12a.
Vivo Y12i Isp Pinout Gadget Review How to reboot vivo y12s to 9008 edl mod: method 1: enable usb debugging. connect phone to pc. send the command via adb. adb reboot edl. method 2 (test point): install qd loader driver on computer. remove back cover of phone & find out the pinout as show in below image. How to reboot vivo y12a to edl mod: install qcom driver on your computer. remove back cover of phone & find out the pinout as show in below image. connect phone to computer by using usb cable. take a coper wire and short that pinout or you can do using tweezer. test point for vivo y12a.